South African Class 5E, Series 1

South African Class 5E, Series 1

Class leader no. E259 at the Bellville Depot, Cape Town, 24 May 2009

Type and origin Power type Electric Designer English Electric Builder English Electric Vulcan Foundry Serial number EE 2163-2222 VF E137-E148 Model EE 5E Build date 1954-1955 Total produced 60

Specifications Configuration: ​  • AAR B-B  • UIC Bo'Bo'  • Commonwealth Bo-Bo Gauge 3 ft 6 in (1,067 mm) Cape gauge Wheel diameter 1,219 mm (48.0 in) Wheelbase 11,279 mm (37 ft 0.1 in)  • Bogie 3,430 mm (11 ft 3.0 in) Pivot centres 7,849 mm (25 ft 9.0 in) Panto shoes 6,972 mm (22 ft 10.5 in) Length: ​  • Over couplers 15,494 mm (50 ft 10.0 in)  • Body 14,631 mm (48 ft 0 in) Width 2,896 mm (9 ft 6.0 in) Height: ​  • Pantograph 4,089 mm (13 ft 5.0 in)  • Body height 3,937 mm (12 ft 11.0 in) Axle load 21,591 kg (47,600 lb) Adhesive weight 86,364 kg (190,400 lb) Loco weight 86,364 kg (190,400 lb) Power supply Catenary Current source Pantographs Traction motors Four EE 529  • Rating 1 hour 377 kW (506 hp)  • Continuous 325 kW (436 hp) Gear ratio 18:67 Loco brake Air & Regenerative Train brakes Vacuum Couplers AAR knuckle

Performance figures Maximum speed 97 km/h (60 mph) Power output: ​  • 1 hour 1,508 kW (2,022 hp)  • Continuous 1,300 kW (1,700 hp) Tractive effort: ​  • Starting 200 kN (45,000 lbf)  • 1 hour 128 kN (29,000 lbf)  • Continuous 104 kN (23,000 lbf)

Career Operators South African Railways Spoornet Impala Platinum Driefontein Class Class 5E Power class 3 kV DC Number in class 60 Numbers E259-E318 Nicknames Klein Mamba (Little Mamba) Delivered 1955-1956 First run 1955

The South African Railways Class 5E, Series 1 of 1955 was an electric locomotive.

In 1955 and 1956, the South African Railways placed sixty Class 5E, Series 1 electric locomotives with a Bo-Bo wheel arrangement in mainline service. The Class 5E introduced what eventually became the most prolific locomotive body shape to ever run on South African rails.

To cope with increased traffic loads on the South African Railways (SAR) in the 1950s, the capacity of its 3 kV DC electrified lines had to be increased. Since more sections in Natal and Transvaal were being electrified, the SAR placed an order for the design and production of a new and more powerful Bo-Bo mainline electric locomotive with English Electric (EE) in 1952. Sixty Class 5E, Series 1 locomotives were delivered and placed in service in 1955 and 1956, numbered in the range from E259 to E318.

The first 48 units, numbered in the range from E259 to E306, were built at the Dick Kerr works of EE in Preston in 1954 and 1955, while the construction of the last twelve, numbered in the range from E307 to E318, was subcontracted to Vulcan Foundry. These twelve, with EE works numbers in the range from 2211 to 2222, were therefore also allocated Vulcan works numbers in the range from E137 to E148.

They were delivered in a bottle green livery with red cowcatchers, initially without the yellow lines and whiskers which were added later to improve their visibility. Since the long Class 4E was already nicknamed Groen Mamba (Green Mamba) by Cape Western enginemen, the shorter Class 5E promptly became the Klein Mamba (Little Mamba) when they first appeared on that section, while the Class 4E was "promoted" to Groot Mamba (Large Mamba). Beginning in 1960, a Gulf Red and yellow whiskers livery gradually replaced the green and yellow.

With both the bottle green and later the Gulf Red SAR liveries, the units had red cowcatchers, except in the Cape Western region. Locomotives based at the Bellville Depot could be identified by their yellow cowcatchers.

These dual cab locomotives had a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end was marked as the no. 2 end. A corridor along the centre of the locomotive connected the cabs, which were identical except that cab 2 was where the handbrake was located.

While the locomotive itself used air brakes, it was only equipped to operate trains with vacuum brakes. While hauling a train, the locomotive's air brake system would be made subordinate to the train's vacuum brake system and would come into operation as the vacuum brakes were being applied, gradually building up to its maximum of 350 kilopascals (51 pounds per square inch). While working a train downgrade, the locomotive's regenerative braking system would also work in conjunction with the train's vacuum brakes.